- 您现在的位置：买卖IC网 > Sheet目录337 > LT3597EUHG#PBF (Linear Technology)IC LED DRIVER TRPL STP DWN 52QFN
LT3597
PIN FUNCTIONS
BOOST1, BOOST2, BOOST3 (Pins 2, 48, 39): Boost
Capacitor Pin. This pin is used to provide a voltage that
is higher than the input voltage when the switch is on to
supply current to the switch driver.
SW1, SW2, SW3 (Pins 4, 46, 41): Switch Pin. Connect
the inductor, catch diode and boost capacitor to this pin.
DA1, DA2, DA3 (Pins 6, 44, 43): Catch Diode Anode.
This pin is used to provide frequency foldback in extreme
situations.
FB1, FB2, FB3 (Pins 7, 34, 35): Feedback Pin. This pin is
regulated to the internal bandgap voltage. The maximum
Buck output voltage can be set by connecting this pin to
a resistor divider from VOUT1-3.
EN/UVLO (Pin 9): Enable and Undervoltage Lockout Pin.
Accurate 1.51V threshold. UVLO threshold can be pro-
grammed by using a resistor divider from V IN . If function
is not required, pin can be tied to the VIN pin.
T SET (Pin 11): Thermal Regulation Pin. Programs the
LT3597 junction temperature at which LED current begins
to derate.
V REF (Pin 12): 2.0V Reference Output Pin. This pin can
sources up to 200μA and can be used to program TSET
and CTRLM.
CTRLM (Pin 13): Master Control Pin. LED current derating
vs temperature is achievable for all channels if the voltage
on CTRLM has a negative temperature coefficient using an
external NTC resistor in a voltage divider from VREF.
I SET1 , I SET2 , I SET3 (Pins 14, 15, 16): LED Current Pro-
gramming Pin. A resistor to ground programs full-scale
LED current.
RT (Pin 17): Switching Frequency Programming Pin. A
resistor to ground programs the switching frequency
between 200kHz and 1MHz.
GND (Pin 18, Exposed Pad Pin 53): Ground Pin. This is
the ground for both the IC and the switching converters.
Exposed pad must be soldered to PCB ground.
V OUT1 , V OUT2 , V OUT3 (Pins 19, 22, 23): Buck Output. This
is the buck regulator output voltage sense into the IC.
LED1, LED2, LED3 (Pins 20, 21, 24): Constant Current
Sink Pin. These are 3 LED driver outputs, each containing
an open collector, constant current sink. All outputs are
matched within ±2% and are individually programmed up
to 100mA using an external resistor at the ISET1-3 pin.
Outputs are rated to allow a maximum VOUT1-3 of 42V.
Connect the cathode of the LED string to LED1-3. Connect
the anode of the LED string to VOUT1-3.
FAULT (Pin 25): Fault Detection Pin. Open collector pin
used to report open LED faults. FAULT must be externally
pulled to a positive supply through a resistor.
NC (Pin 26): No Connection Pin. Tie to ground.
SYNC (Pin 27): External Clock Synchronization Pin. When
an external clock drives this pin, the Buck regulators are
synchronized to that frequency. Frequency programmed
by the RT pin resistor must be at least 20% less than the
SYNC pin clock frequency.
PWM1, PWM2, PWM3 (Pins 30, 29, 28): PWM Dimming
Control Pin. When driven to a logic high, the LED1-3 current
sink is enabled. If PWM dimming is not desired, connect
the pin to VREF. Channels can be individually disabled by
tying PWM1-3 to ground.
CTRL1, CTRL2, CTRL3 (Pins 33, 32, 31): Analog Dimming
Control Pin. This pin is used to dim the LED current in an
analog fashion. If the pin is tied to a voltage lower than
1.0V, it will linearly reduce the LED current. If feature is
unused, connect the pin to VREF.
BIAS (Pin 37): Supply Pin. This pin is the supply for an
internal voltage regulator to internal analog and digital
circuitry. BIAS must be locally bypassed with a 2.2μF
capacitor.
V IN (Pins 50, 51): Input Supply Pin. V IN must be locally
bypassed with a 10μF capacitor to ground. Pins 50 and
51 are internally fused.
3597fa
8
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LT3598IUF#PBF
IC LED DRIVR WHITE BCKLGT 24-QFN
LT3599IFE#PBF
IC LED DRVR WHITE BCKLGT 28TSSOP
LT3743EFE#PBF
IC LED DVR HP CONST CURR 28TSSOP
LT3745IUJ#TRPBF
IC LED DVR 16CH 50MA 40QFN
LT3746IUHH#TRPBF
IC LED DRIVER 32CHANNEL 56-QFN
LT3754IUH#TRPBF
IC LED DVR 16CH 50MA 32QFN
LT3755EMSE#PBF
IC LED DRVR HP CONS CURR 16-MSOP
LT3760EFE#PBF
IC LED DVR WHT/CLR BCKLT 28TSSOP
相关代理商/技术参数
LT3597EUHG#TRPBF
功能描述:IC LED DRIVER 60V TRIPLE 52-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3597IUHG#PBF
功能描述:IC LED DRIVER 60V TRIPLE 52-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3597IUHG#TRPBF
功能描述:IC LED DRIVER 60V TRIPLE 52-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3598
制造商:LINER 制造商全称:Linear Technology 功能描述:60V Triple Step-Down LED Driver Programmable Temperature Protection
LT3598_1
制造商:LINER 制造商全称:Linear Technology 功能描述:6-String 30mA LED Driver with 1.5% Current Matching
LT3598EFE#PBF
功能描述:IC LED DRVR WHITE BCKLGT 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3598EFE#PBF
制造商:Linear Technology 功能描述:LED DRIVER BOOST PWM 2.5MHZ 制造商:Linear Technology 功能描述:LED DRIVER, BOOST, PWM, 2.5MHZ, TSSOP-24
LT3598EFE#TRPBF
功能描述:IC LED DRVR WHITE BCKLGT 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND